1989 Nissan GT-R R32 Skyline

Description

Available now from RMC Miami is this beautiful 1989 R32 GTR Skyline.
This R32 was imported in 2015 and has had 1 very meticulous owner since being here stateside in Miami Florida.
Our Skyline is a very clean example, the body does not have any rust and the paint is in excellent condition. The car has spent
its life here in Florida garage kept and mainly used as a weekend car. Recently the whole car was paint corrected wrapped in
paint protection film and fully ceramic coated giving it the incredible deep glossy shine you see in the photos. Body lines are
straight, subtle but gorgeous and rare upgrades to the exterior include fully powered carbon fiber Ganador mirrors and a rear
carbon fiber gurney flap by Fujimura. Aftermarket wheels are wrapped in newer Achilles tires on all 4 corners.
Suspension has been completely revamped. Apexi Coil over suspension is tight, all 4 corners, there is no rattles or weird noises and
the dampening is dialed in nicely. The car handles like its on rails and the ride is smooth with no rubbing of any kind. In addition to the
coils aftermarket sway bars have been added front and rear to eliminate a lot of the body roll these cars have at stock height.
The car has upgraded twin turbos, Garrett GT 2860's makes over 500 wheel horsepower on pump has but also is E85 capable. a custom single throttle body manifold has been installed with a 90MM throttle body/
Clutch is an OS giken sprung twin disc clutch. Computer is a Haltech pro. Exhaust is a custom stainless steel straight pipe. Under the valve cover you find HKS Cam gears and Tomei Cams.
Modifications mechanically are extensive and done with all quality parts in what many call a "no expense spared" style
Last year alone over ,000 in labor spent not including parts...
-Full HICAS removal. Disassemble rear hicas part of power
steering pump, weld inlet, route lines, remove master pump, slave
and lines. Reroute power steering lines to bypass HICAS system
-Powdercoat, remove valve cover, coil pack cover timing cover and
deliver to Powder coater along with intake manifold. Pickup upon
completion. Reinstall with new stainless hardware, new half moon
seals,new valve cover seals.
-Remove Factory Oil cooler, Delete heater core lines, fabricate
merge tube for coolant block passages, measure and replace
hoses with silicone lines and new clamps
-Battery Relocation install and cable construction and routing.
Weld ground post, assemble and mount battery box and hardware
-Fuel system upgrade: Change lines to -06 AN, this includes
measuring and fabricating the lines and hose ends to work with
new fuel rail and routing. Install bulkheads in factory fuel hat,
Mount Fuel Pressure Regulator, trim and line trunk space to
clearance new lines, install filter and e85 content sensor
Oil Cooler, Fabricate servicable brackets and mount oil cooler.
Weld mount for remote oil filter adapter, clearance lines on
transfer case for new oil lines. Remove Factory oil filter bracket.
Fabricate duct, lines, and hose ends. Install oil pressure gauge
fitting and -04 line, route to dash. Install factory oil pressure
sender unit in block using adapter.
Intake: Setup Fittings and VAC block, Route vac lines. Modify
IACV. Fit Coolant distribution block, weld in fitting for turbo feed,
install coolant temp sensors. Modify coolant tank, close inlet,
modify swirl pot ro clearance TPS and Fan Shroud
Throttle cable construction, dissassemble factory sheath and
ends, replace with lokar cable and fit / mount for proper throttle
function
Intercooler Piping: Modify driver side outlet of intercooler to
clearance duct for oil cooler. Mount BOV in new position, install
IACV port,Fabricate both charge pipes, size and fit couplers,
change clamps to T-bolt style. Paint with Wrinkle Black finish,
including refinishing of BOV and painting brackets in engine bay to
match.
Electrical: Build individual harnesses for Fuel pressure sensor, E85
content sensor, and MAC boost solenoid. Route into dash and
pinout aux plug for haltec. Extend coolant plug for new sensor
location. Picked up pins from Local supplier, Build Ground post for
harness in engine bay, wire up oil pressure gauge light.
Water pump:remove radiator, remove timing gear cover, remove
crank pulley, remove dist cover, and both tensioners, unbolt
water pump, reinstall new pump and sealant, reinstall all
components, set timing of engine,
sync timing with Haltec.
Clutch Dampener removal
remove intercooler piping and brackets for swirlpot, paint in
wrinkle finish black, reinstall
Depin aux plug for haltech, pin new plug for I/O box, prog new parameters in Haltech Computer
Interior is in good shape and largely original. The steering wheel has been upgraded to a NARDI steering wheel. The entire air conditioning system has been refreshed with all new and original
parts. It is the coldest AC we have felt in any of the R32 Skylines we have had. Shifter is IRP brand from belgium with a really nice short throw.
This particular GTR is as turn key as they come. It is dialed in and in really good shape. Underneath the car is really clean the frame rail are straight and no rust which
is really hard to find on these cars. The purchase will include all service records and clean Florida title.
vin is
bnr32004085
Please see the car below on video with walkaround cold start and in car
https://youtu.be/Bu6Uq7IP5ek
Serious inquiries Call Eddie 305-527-6867 or Bernard 305-443-7626
Follow us on Instagram for live updates!
@rmcmiami
We also speak Deutsch and Español
Can Ship (Insured) Anywhere Worldwide if Needed.
Located in Miami, Florida 33126
Financing Available with Approved Credit
Trades Always Welcomed (UP or DOWN)